Difference between revisions of "DVD"

From SDA Knowledge Base

Jump to: navigation, search
(Option 2: ohshitibrokeit!!!)
(Added lag reduction method)
Line 11: Line 11:
 
===Reducing Lag===
 
===Reducing Lag===
  
There are several ways to reduce lag and play normally.
+
There are several ways to eliminate lag and play normally.
  
 
1. Use a [http://www.radioshack.com/product/index.jsp?productId=2103065 powered splitter]. Basically, you plug in the video and audio from your console, and it sends it to two different places (your TV and your DVD recorder). This will completely eliminate lag, but costs about $45, and you won't be recording S-Video unless you use an S-Video cable to connect the console to the splitter AND the splitter to the DVD recorder.
 
1. Use a [http://www.radioshack.com/product/index.jsp?productId=2103065 powered splitter]. Basically, you plug in the video and audio from your console, and it sends it to two different places (your TV and your DVD recorder). This will completely eliminate lag, but costs about $45, and you won't be recording S-Video unless you use an S-Video cable to connect the console to the splitter AND the splitter to the DVD recorder.
Line 19: Line 19:
 
<font color="green"><b>Note:</b> There are two kinds of S-Video cables--ones that connect your console to an S-Video in and ones that connect an S-Video out to an S-Video in. The former are usually inexpensive; the latter are quite spendy. Make sure you buy the correct kind.</font>
 
<font color="green"><b>Note:</b> There are two kinds of S-Video cables--ones that connect your console to an S-Video in and ones that connect an S-Video out to an S-Video in. The former are usually inexpensive; the latter are quite spendy. Make sure you buy the correct kind.</font>
  
3. Connect your console to a VCR, then use the RF out (a cable that sometimes has a screw on the end) of your VCR to connect it to your TV and the composite out (red, white, and yellow cables) to connect it to your DVD recorder. This won't cost anything, assuming you already own a VCR with composite in/out and RF out, but you will be recording composite video instead of S-Video.
+
3a. Connect your console to a VCR, then use the RF out (a cable that sometimes has a screw on the end) of your VCR to connect it to your TV and the composite out (red, white, and yellow cables) to connect it to your DVD recorder. This won't cost anything, assuming you already own a VCR with composite in/out and RF out, but you will be recording composite video instead of S-Video.
 +
 
 +
3b. Similar to above, but if your console happens to have both an RF out and a composite out, you can skip the VCR; just send the RF to your TV and the composite to your DVD recorder.
  
 
4. In PAL regions you can use the bidirectionality of SCART to record composite quality video by plugging your console into your TV then your TV into your DVD recorder's input with a SCART cable.
 
4. In PAL regions you can use the bidirectionality of SCART to record composite quality video by plugging your console into your TV then your TV into your DVD recorder's input with a SCART cable.

Revision as of 23:44, 19 February 2008

Overview

Recording with a DVD recorder will produce far superior quality than recording with a VCR, so it is well worth the investment. Also, being a digital format, it poses far less "traps" to deal with than VHS. When you record with a DVD recorder, be sure to use SP or better speed. See your DVD recorder's manual for more info about this. You will wreck the quality of your run if you record on a speed worse than SP. Before you even purchase a DVD recorder, make sure to think about recording medium. If you decide to mail your DVD(s) to me for processing, proceed to the submission guidelines for information about how to contact SDA. Otherwise, if you want to try to encode your run yourself, read here. However, there is one problem that needs to be taken care of whether or not you encode by yourself: lag.


Lag

When recording with a VCR, you hook your console's video out into the VCR, and you hook the VCR to your TV. The signal travels from the TV to the VCR, which records it, then sends it to the TV to be displayed. Because of the way the VCR writes the data on the tape, there is no lag. However, when a DVD recorder is hooked up in this fashion, it must digitize the data and, in our case, record it before outputting it. Unfortunately, no DVD recorder out on the market is able to do this instantaneously. Therefore, you will see and hear what was really happening about a half-second or so ago. Obviously, this can really mess with your ability to play the game well.


Reducing Lag

There are several ways to eliminate lag and play normally.

1. Use a powered splitter. Basically, you plug in the video and audio from your console, and it sends it to two different places (your TV and your DVD recorder). This will completely eliminate lag, but costs about $45, and you won't be recording S-Video unless you use an S-Video cable to connect the console to the splitter AND the splitter to the DVD recorder.

2. Use an S-Video cable. This cable has four plugs-the three standard yellow, white, and red plugs and an S-Video plug. This lets you plug the S-Video plug and the two audio plugs (the white and red ones) into your DVD recorder and the composite video (yellow) plug into your TV. This eliminates video lag and lets you record S-Video, but you won't have audio on your TV unless you connect your DVD recorder and your TV with the white and red audio plugs. This will cause the audio on your TV to lag behind the video, which may or may not affect your playing ability. These cables are very inexpensive-they can be found for around $5.

Note: There are two kinds of S-Video cables--ones that connect your console to an S-Video in and ones that connect an S-Video out to an S-Video in. The former are usually inexpensive; the latter are quite spendy. Make sure you buy the correct kind.

3a. Connect your console to a VCR, then use the RF out (a cable that sometimes has a screw on the end) of your VCR to connect it to your TV and the composite out (red, white, and yellow cables) to connect it to your DVD recorder. This won't cost anything, assuming you already own a VCR with composite in/out and RF out, but you will be recording composite video instead of S-Video.

3b. Similar to above, but if your console happens to have both an RF out and a composite out, you can skip the VCR; just send the RF to your TV and the composite to your DVD recorder.

4. In PAL regions you can use the bidirectionality of SCART to record composite quality video by plugging your console into your TV then your TV into your DVD recorder's input with a SCART cable.


Using Multiple Discs

It will be necessary for you to change discs mid-run if your single-segment run runs longer than 2 hours (a standard DVD holds only 2 hours of video at SP, the lowest allowable quality/speed). Simply pause the game, stop the recording, change discs, start recording again, then unpause the game and continue your run. Either you or nate can rejoin the run before the encoding phase. Be sure to record plenty of time at the pause screen on both discs (30 seconds should be sufficient) so that you don't accidentally miss recording part of your run, which is grounds for rejection.


Self Encoding

Turn on file extensions in Windows by going to Windows Explorer -> Tools -> Folder Options -> View, uncheck "Hide extensions for known filetypes".

Make sure to finalize the DVD before continuing with this guide. Finalizing is done on the DVD recorder itself. DVD-RAM and DVD+RW are the only exceptions.

You will need to install a large number of separate pieces of software to get your run off of the DVD and encode it to H.264 / Xvid. All of this software only runs on Microsoft Windows, so you will need to have access to a computer running Windows to proceed.


DVD software installation

Download the latest version of DGMPGDec utilities by Donald Graft and extract the contents to "C:\Program Files\DGMPGDec". This folder contains the DGIndex.exe application and the important DGDecode.dll file. Leave this folder alone for the moment.


Extracting the DVD source files

You have two options. You can either copy the contents of the whole DVD, which can be up to 4.3 GB of data, or copy only specific parts such as your successful attempts. If you plan to send your DVD files to Nate over the Internet, you'll be following the second option.

Insert the finalized DVD into the DVD drive in your computer (if the DVD has not been finalized in the DVD recorder, it probably won't work).


Option 1

Navigate to your DVD drive and select all of the files from the VIDEO_TS folder on the DVD you inserted. Copy them to a folder where you will do your video processing.

DVDsourcefiles.png


Option 2

Open DGIndex.exe inside the DGMPGDec directory you unzipped during the software installation. Go to Audio -> Output Method and set it to demux all tracks. Load the vob files either from your hard drive or (more likely) straight from the disc. Use the slider to move to the place where you want to make your starting cut and press the left bracket button. As you can see in the picture I've decided to start the cut at the menu screen, and have yet to specify an end point which I'm sure you can handle by yourself now.

Dgindexcut.jpg

Once you've done that, go to File -> Save Project and Demux Video. This will create an m2v video file, an ac3/mpa/wav sound file, and a d2v file. DO NOT CHANGE THE NAME OF THE AUDIO FILE!

Delete the d2v file. It is useless since it is still pointing at the files on the DVD.

At this point, if you're sending in your files to SDA, then you have all you need. Otherwise continue to the next section where you will create a fresh d2v file which will be pointing to the m2v file instead of the DVD.


Creating the project file (.d2v)

Open DGIndex.exe inside the DGMPGDec directory you unzipped during the software installation. Go to Audio -> Output Method and set it to demux all tracks. Now go to File -> Open, or just hit F2 and navigate to your video processing folder.

  • If you chose Option 1, you should select ALL (yes, ALL) of the .VOB (or .VRO) files. If you have more than one, use the "Add" button. For the files named something like "VTS_01_1.VOB" and "VTS_01_2.VOB," put them in order of number. If you have a file called "VIDEO_TS.VOB," put it before the others.
  • If you chose Option 2, select the m2v file.

Hit OK twice to proceed to the main screen. From here, simply go to File -> Save Project and save the file with a name you can remember.


Important: Both options result in the extraction of an audio file. The filename will look something like "vob T01 2_0ch 192Kbps DELAY -84ms.ac3". MAKE SURE that you keep the part that I've underlined as this information is needed later on. Even if the delay is 0, leave it alone, it's good to be consistent.

Note: If you load up your file in DGIndex and get something like this, try unzipping this file and loading it into DGIndex with the rest of your vob/vro files. Move it to the top of the file list and click OK; you should see a menu-like screen and, if you move the slider at the bottom, your file.


You can now proceed to the AviSynth page.


Return to the front page.

Personal tools